(17) NEW 316L S/S Processors & Mix Tanks – NEW Desalination/RO System

A&B Process Systems

Date & Time

April 27 - May 1, 2015

9:00 AM

Location

Online Only

(3) NEW – NEVER INSTALLED A&B Process Systems 7,500 Gallon 316L S/S, Jacketed Processor Tanks

  • ASME Heat transfer surface: 150 PSIG @ -20º F to 366º F
  • Dimensions: 126″ O.D. shell x 144″ straight wall x 130″ OD outer shell
  • Pitched-bottom
  • CIP Spray Ball: 1.5″ single spray ball
  • All interior welds taped off, ground and polished to a #4; All tanks passivated
  • Side Scrape Agitator and Drive Assembly: Scraper blade agitator constructed from sch. 40 pipe with 6” wide Teflon blades scraping dimple surfaces on the bottom and side wall, with A&B Process Systems™ Quick Change bottom bearing support and 8” diameter Buna drip deflector hood
  • Teflon Blades are rated for Heat transfer temperature of 550° F max: The agitator design is based on a maximum product viscosity of 80,000 Cps.

(4) NEW – NEVER INSTALLED A&B Process Systems 4,205 Gallon 316L S/S, Jacketed Mix Tanks

  • ASME Heat transfer surface: 150 PSIG@ -20° F to 366° F, Plug Welded Dimple Surface on Shell
  • 90″ O.D. shell x 185″ straight wall x 94″ OD outer shell
  • Pitched-Bottom
  • CIP Spray Ball: 1.5″ single spray ball
  • All interior welds taped off, ground and polished to a #4; All tanks passivated

(3) NEW – NEVER INSTALLED A&B Process Systems 7,500 Gallon 316L S/S Single Wall Cone-Bottom Mix Tanks

  • Dimensions: 126″ O.D. shell x 144″ straight wall x 130″ OD outer shell
  • Cone-bottom with a 150° inclusive angle
  • CIP Spray Ball: 1.5″ single spray ball
  • All interior welds taped off, ground and polished to a #4; All tanks passivated
  • Turbine Agitator and Drive Assembly constructed from sch. 40 pipe with (6) thick x 6” wide x 24” long blades with A&B Process Systems Quick Change bottom bearing support 8” diameter Buna drip deflector hood
  • Agitator design is based on a maximum product viscosity of 80,000 Cps

(7) NEW NEVER INSTALLED A&B Process 5,205 Gallon, 316L SS Single Wall Cone-Bottom Mix Tanks

  • 90″ O.D. shell x 185″ straight wall x 94″ OD outer shell
  • Cone-Bottom with a 150° inclusive angle
  • CIP Spray Ball: 1.5″ single spray ball; All tanks passivated

(36) NEW – NEVER INSTALLED Coti Global Compression Load Cells, Model GC-16-SSW

NEW – NEVER INSTALLED – Watec CI-250K-2 Desalination / Reverse Osmosis System

  • NEW COST EXCEEDED $1 MILLION
  • Watec CI-250K-2 Seawater Desalination System, can produce 250,000 gallons of fresh water per day; uses thin-film semi-permeable membrane to separate fresh water from the salt in seawater. Centrifugal multi-stage pumps achieve 1100 psi water pressure to drive the reverse osmosis process. The fresh water is routed to storage by a pump and the high pressure brine is routed through an energy recovery device.
  • Seawater is introduced through a 15-micron absolute bag filter. The finishing filter is a 2-micron cartridge filter. Inlet flow is controlled with a flow transmitter and valve.
  • Protec Pro8-1200-MSP-6 membrane vessels spun of reinforced fiberglass with burst pressure of greater than 5,000 psi.
  • Interstage Booster Pump: Carver RS9-BCP 3 stage pump supplies booster pressure for the second stage of the unit.
  • High Pressure Charge Pump: Carver RS 9-BCP 15 stage pump develops 2,090 feet of head with a 25 psig suction pressure and is equipped with a 200 hp Baldor motor.